- Brake-type low-table disc injection molding machine: an efficient and stable manufacturing solution!
- The present situation and trend of China machine industry
- What do you need to pay attention to before the vertical injection machine is shut down
- The increase of injection products -- the popularity of injection molding machine is just around the corner.
- The factors that affect the molding of the vertical injection molding machine
Contacts:Hanna WANG phone:0769-81929376 Email:waimao005@dg-taifu.com address:Fulong Yangwu Industrial Area, Shipai Town, Dongguan City, Guangdong Provice, China
What do you need to pay attention to before the vertical injection machine is shut down
source: time:2018-04-14 Click:4652
A vertical injection molding machine should be checked when starting.
1. check for actuating oil: determine whether the vertical oil injection volume of the injection molding machine is between the lowest limit and the highest limit of the oil meter. The oil content of the automatic lubricator is suitable.
2. check for cooling water: make sure that the cooling water pipe system of vertical injection molding machine has no leakage phenomenon and adequate water volume, so as to maintain normal cooling effect.
3. temperature opening and checking: determine whether the heat of the dryer, pipe and die is normal, especially the temperature of the vertical injection molding machine must be completely reached the set temperature, and the action of shooting, releasing and hanging can be done.
4. inspection of safety door and safety guide rod: determine the opening and closing of the vertical injection molding machine safety door, and whether the contact between the safety door and the limit switch and the pressure relief valve is normal. Confirm whether the location of safety guide rod is proper and whether it is locked. The red emergency stop button on the front and rear operation box is normal, so as to ensure the safety of users.
5. check the lubrication device: whether the oil quantity of the butter mouth is sufficient, whether the time setting of the oil injector is proper or not, and whether the pipeline of the oil injection device is clear.
6. inspection of the active machine parts: all the active parts on the vertical injection molding machine need to be properly lubricated, and remove the impurities and dust from the active parts, keep the smooth and clean surface of the active friction surface, and do not put the tools on the active parts to prevent the damage when the machine is operated.
7. check for low pressure die closing device of vertical injection molding machine: correct the low pressure die closing device correctly, so as to ensure mould safety.
8., check other conditions: whether the temperature, pressure, speed, time and distance of various settings are appropriate.
9. inspection of the operation of the empty car: the low pressure can be fully automatic operation, so that the empty car runs about 10~30 minutes, and after a continuous stable condition, it can be formally operated.
10. examination of the sound of the sound: recording the normal operation sound and the sound of the oil pressure pump, it can detect the abnormal phenomena such as the filter blocking, the suction air, the internal wear and so on. The buzz of the solenoid valve is related to the impurities in the inner axis, and the buzz of the relay and the electromagnetic contactor shows that the dirt and dust exist between the contact points. . Checking the causes of abnormal sounds is a great help for prevention of injury.
Two, the vertical injection molding machine should be checked when shutting down.
1., close the material gate of the hopper, reduce or turn off the heating of the hopper (depending on the downtime). The plastic tube completely shot, especially the material is acidic and corrosive must implement the.
2., clean and wipe the mould of vertical injection molding machine and do rust treatment.
3., if the die is not unloaded, do not extend the curling hand.
4. turn off the cooling water and cut off the power supply.
5. vertical injection machine platform cleaning inspection and so on.
Recommended Products MORE+
-
15 Ton Standard Vertical Injection Molding Machine TFV2-15
-
20 Ton Standard Vertical Injection Molding Machine TFV4-20
-
120 Ton Rotary Vertical Injection Molding Machine TFV4-120R2
-
35 Ton Standard Vertical Injection Molding Machine TFV4-35
-
55 Ton Standard Vertical Injection Molding Machine TFV4-55
-
Motor Rotor
-
Plastic Overmolding
-
Terminals
-
Plastic Accessories
-
SIM Card Tray Holder Slot
Recommended News MORE+
- What are the domestic injection models2018-04-14
- The factors that affect the molding of the vertical injection molding machine2018-04-14
- Noise analysis of horizontal injection molding machine2018-04-14
- Vertical injection molding machine classification, good choice, make entrepreneurship easier.2018-04-14
- The present situation and trend of China machine industry2018-04-14
- Precautions for the hydraulic system operation of the slider injection molding machine2018-04-14
- Pay attention to the vertical injection molding machine and the maintenance of common sense2018-04-14
- Industry market of vertical injection molding machine2018-04-14
- Disc vertical injection molding machine, the best choice of small and medium-sized parts.2018-04-14
- The increase of injection products -- the popularity of injection molding machine is just around the corner.2018-04-14